; AST Windows Release Notes
;===============================================================================
v.1.06.00: ycchen@112217
01.[Bug][AST2500] disable fast reset after DRAM initial by H/W request
------------------------------------------------------------------------------- 
v.1.05.00: ycchen@092617
01.[Bug][AST2500] Fixed system resume cause BMC fw reset issue
------------------------------------------------------------------------------- 
v.1.04.03: ycchen@091117
01.[Bug] [AST2500] Fix stress test failed if alert #EXTRST to low
v.1.04.00: ycchen@052317
01.[New] [AST2500+DP501] Support AST2500 + DP501
02.[New] [AST2500] Modify DRAM Settings by H/W request (2017_03_30)
03.[Bug] [AST2400/2500] Fixed drag windows cause garbage issue in 1920x1200
-------------------------------------------------------------------------------
v.1.03.04: ycchen@121616
01.[Bug] [AST2400/2500] disable XDMA if P2A is disabled
v.1.03.00: ycchen@070616
01.[Bug] [AST2500] Fixed USB unknown device issue
02.[Bug] [AST2500] Fixed failed to initial DRAM if enable GPIOZ7
03.[New] [AST2400/2500] Support AST2400/2500 + ANX9807
04.[New] [DP501] Add S/W Reset for the platform lack of H/W Reset
-------------------------------------------------------------------------------
v.1.02.07: ycchen@032116
v.1.02.06: ycchen@022416
01.[Bug] Improve Lag issue if connect many(more than 8) web cams
v.1.02.05: ycchen@121515
01.[New] [AST2500] Modify by H/W request (2015_12_12)
v.1.02.04: ycchen@112315
01.[New] [AST2300/2400] New DRAM Setting by H/W request
v.1.02.02: ycchen@082415
01.[New] [AST2400/2300] Support DRAM Auto Sizing in VGA only mode
02.[New] Support 1152x864 75Hz
v.1.02.01: ycchen@072715
01.[New] Add options for inhibit P2A Access
02.[New] [AST2400/2500] Support 25MHz V-PLL reference Clock
-------------------------------------------------------------------------------
v.1.01.05: ycchen@052715
01.[Bug] [AST2500] Fixed Screen Shift Resume from Screen Off
02.[Bug] [AST2500] Fixed 1680x1050 display abnormal issue on DELL 2410 monitor
03.[New] [AST2500] Support AST2500 VGA only mode(without BMC)
v.1.01.04: ycchen@041315
01.[Bug] [AST2500] Fixed 1600x900 CVT without RB did not display properly
02.[Bug] [AST2500] Fixed Threshold Issue for reduced blank mode
v.1.01.03: ycchen@040215
01.[Bug] [AST2500] Fixed ast2500a0 cannot boot to Windows
02.[Bug] [AST2500] Recover E2M for AST2500A0
03.[New] [AST2500] Remove AST2500A0 VCLK patch for AST2500A1 and after
04.[Bug] [DP501] Fixed cannot display issue with 2-lanes design
05.[Bug] [DP501] Fixed sw reset cause screen blank issue
06.[Bug] [ITE66121] Fixed screen blank issue sometimes
v.1.01.02: ycchen@022615
01.[New] Support 1600x900 CVT mode
v.1.01.01: ycchen@020915
01.[Bug] [AST2500] Disable E2M for AST2500A0
02.[New] Show "ASPEED Video BIOS" if driver cannot get VBIOS version properly
03.[Bug] Modify for CVT reduced blank parsing criteria
04.[Bug] [DP501] Migrate boot.bin to v.1.01.01 for BMC fw IRQ8 increase issue
-------------------------------------------------------------------------------
v.1.00.07: ycchen@091714
01.[Bug] [ITE66121] Fixed cannot display properly through ITE66121
02.[Bug] [AST1400] Fixed AST1400 cannot support wide screen mode
03.[New] [AST2400] Enable PCI AER by default
v.1.00.05: ycchen@072414
01.[New] Show "ASPEED Video BIOS" if driver cannot get VBIOS version properly
02.[New] Show "AST1400/2400" instead of "AST2400" for AST1400/2400 product
03.[Bug] [DP501] Fixed Win2008R2 BSOD Issues
04.[Bug] Remove 1600x1200 for ASUSP238 monitor
-------------------------------------------------------------------------------
v.0.99.10: ycchen@032114
01.[Bug] [DP501] Fixed screen blank if resume from Hibernate
v.0.99.09: ycchen@030414
v.0.99.08: ycchen@022014
01.[Bug] [DP501] Fixed Screen Blank Sometimes and need to re-plug to resume
02.[Bug] Fixed monitor "out of range" issue when hibernate
v.0.99.07: ycchen@012414
01.[Bug] [DP501] Fixed Screen Blank Sometimes and need to re-plug to resume
v.0.99.06: ycchen@010714
01.[Bug] [DP501] Fixed Screen Blank Sometimes even re-plug DP connector
v.0.99.05: ycchen@010204
01.[Bug] [DP501] Fixed Screen Blank Sometimes Issue
02.[Bug] [SIL164] Fixed Screen Blank Resume from Suspend
03.[New] [DP501] Modify for Lenovo Ramjet and Renegade SDV
v.0.99.04: ycchen@120613
01.[Bug] [DP501] Fixed EDID cannot be read properly when system reset
v.0.99.03: ycchen@120313
01.[Bug] [AST2400 + DP501] Fixed screen noise issue when system reset
02.[Bug] Fixed 1600x1200 will be disabled if the prefer timing of the monitor is 1920x1080
v.0.99.01: ycchen@112113
01.[Bug] [AST2400 + DP501] Fixed DP Dongle Compatible Issue
v.0.99.00: ycchen@111513
01.[New] [AST2400] Support AST2400 + DP501
-------------------------------------------------------------------------------
v.0.98.01: ycchen@092313
01.[New] Use MMIO instead of IO port access
v.0.98.00: ycchen@073013
01.[Bug] [AST2400] Fixed display abnormal issue if move window under Win2008R2 on Denlow platform
02.[Bug] [AST2400] Fixed Text Content Disappearred issue under Win2008R2
03.[Bug] [ite66121] Fixed I2C interrupt be trigerred issue
-------------------------------------------------------------------------------
v.0.97.06: ycchen@022013
01.[Bug] [AST2000] Fixed display abnormal issue
02.[New] Modify for Read EDID Stability
v.0.97.05: ycchen@122512
01.[New] Remove Wide Screen Mode if the prefer timing of the monitor is not wide screen mode
v.0.97.04: ycchen@121112
01.[New] Support ITE66121 on AST2300/2400
02.[Bug] [AST2300/2400] Modify DRAM Setting by H/W request
-------------------------------------------------------------------------------
v.0.96.00: ycchen@090512
01.[Bug] Fixed 1920x1080 Screen not Full on SAMSUNG SyncMaster BX2231
02.[New] Support 1600x900 60Hz (CVT Reduced Blank)
03.[Bug] [AST1300] Fixed AST1300 cannot support wide screen mode
04.[New] Set CVT non-reduced blank as default timing for 1280x800, 1400x900, 1650x1080, ycchen@090512
05.[Bug] [AST2400] Fixed adapter info. in display page is in-correct
-------------------------------------------------------------------------------
v.0.95.01: ycchen@052112
01.[Bug] Fixed iKVM cannot display properly with older VBIOS (before v.0.92.00)
02.[New] [AST2300] Modify DRAM settings by H/W request (2012_05_09)
03.[Bug] [AST2300] Avoid I2C1 lock issue if customer I2C1 layout is not correct
04.[New] Support 1360x768 60Hz
v.0.95.00: ycchen@022911
01.[New] [AST2400] Support AST2400 FPGA, ycchen@111511
-------------------------------------------------------------------------------
v.0.94.02: ycchen@102211
01.[Bug] Fixed performance test - image rendering test take too long time issue, ycchen@102211
02.[New] [AST2300] Remove the patch for v.0.94.00 #4, Fixed in AMI CRB014 BIOS finally, ycchen@102811
v.0.94.01: ycchen@092211
01.[Bug] Fixed paring modes issue with Samsung syncmaster 245B monitor
02.[Bug] Fixed 1280x800, 1440x900, 1680x1050 not support 256c modes
v.0.94.00: ycchen@091411
01.[New] Support 1280x800@60Hz, 1440x900@60Hz, 1680x1050@60Hz reduced blank mode
02.[New] [AST2300] Modify DRAM Settings by H/W request (07/06/11), ycchen@081111
03.[New] [AST2300] Modify Reg. info for AST2300 to AST1300/2300
04.[Bug] [AST2300] Fixed ASPM can't be disabled properly on some specific platform, ycchen@090911
-------------------------------------------------------------------------------
v.0.93.09: ycchen@061711
01.[2008R2] Fixed 1600x1200 60Hz didn't show in the mode list if use ASUS VK247H Monitor
v.0.93.08: ycchen@053111
01.[New] [AST2300] Modify MCLK to 396MHz by H/W request
v.0.93.07: ycchen@050911
01.[Bug] Fixed it takes too long time to get EDID from EDID failed monitor
02.[New] Set Default Acceleration Level to Full in INF
v.0.93.06: ycchen@042911
v.0.93.05: ycchen@040711
01.[Bug] Warm boot test may cause system hanged, ycchen@032811
v.0.93.04: ycchen@030411
01.[New] [AST2300] Modify for DDR3 2Gb Support
02.[New] [AST2300] Slow Down CPU/AHB clock in VGA only mode
v.0.93.03: ycchen@021511
01.[New] [AST1180] Add for AST1162 + AST1180, ycchen@012611
02.[Bug] [AST2300] Fixed iKVM Direct Mode Display Abnormal issue if enable Flip, ycchen@011811
03.[New] [AST2300] DRAM Setting Updated by H/W (020811)
04.[New] [AST2100/2150] Enable AST2100/2150 DRAM Calibration by H/W Request (021411)
v.0.93.02: ycchen@122410
01.[Bug] Fixed Display Timing not Meet the Requirement of VESA Timing
v.0.93.01: ycchen@121410
01.[New][AST2300] Modify CRT Threhold by H/W request
02.[New][AST2300] Disable ASPM for AST2300 VGA Only
v.0.93.00: ycchen@121210
01.[Bug] [ASPEED Graphics] Fixed 8bpp support mode list incorrect issue
02.[Bug] [AST1180] Fixed switch media player to full screen mode may cause system hanged
03.[Bug] [AST1160] Disable DAC for DVI out
04.[New] [AST2300] DRAM Setting Updated by H/W (121010)
-------------------------------------------------------------------------------
v.0.92.02: ycchen@100910
01.[Bug] Fixed wave form issue on 1280x1024 75Hz and 1280x800 60Hz
02.[New] Add for UEFI Graphics Driver support, ycchen@102010
03.[New] [AST2300] DRAM type and size selection based on H/W trapping, ycchen@102010
v.0.92.01: ycchen@090110
01.[PATCH] Fixed can't detect PnP monitor properly if enable thinsoft Betwin for ast1160/1180, ycchen@090110
02.[New] AST1180 OSD Support, ycchen@090210
v.0.92.00: ycchen@081110
01.[New] Add More Mode Info to Scratch for General KVM Need
02.[Bug] Fixed AST1180 Screen no off after shutdowm with Betwin, ycchen@070910
03.[Bug] Fixed AST1180 change resolution too long issue, ycchen@070910
04.[New] Modify for AST1180 performance by H/W request, ycchen@080410
05.[New] Add wide screen support check for iKVM backward compatible
06.[New] Add for AST2300 VGA only
07.[New] Enable E->M since AST2300A1
08.[New] Modify for AST2300 support mode list
---------------------------------------------------------------------------------
v.0.91.0A: ycchen@062310
01.[New] Disable XDMA for AST2300 by default
02.[Bug] Disable E2M for AST2300 A0
v.0.91.09: ycchen@062110
01.[New] Add the support for WXGA modes
02.[New] Support AST2300 A0 Chip
v.0.91.07: ycchen@040310
01.[Bug] Fixed Driver be stopped on ASUS's platform if run HCT Stressed Test, ycchen@040310
v.0.91.06:
v.0.91.05:
01.[New] Modify new 2D reset sequence by H/W request
02.[Bug] Remove VirtualEDID support other than AST2000
03.[Bug] Fixed AST2300 line error issue
v.0.91.04: yc_chen@011110
01.[New] Support AST2300 FPGA Boards
02.[New] Add registry for disable mode check (VGA.ulDisableModeCheck)
---------------------------------------------------------------------------------
v.0.90.07: ycchen@100709
01.[Bug] Fixed driver issue on Windows2000
v.0.90.02: yc_chen@090709
01.[Bug] Modify for AST1160 + AST1180 FPGA, ycchen@090309
02.[Bug] Patch can't shutdown properly on Win7, ycchen@090709
v.0.90.01: yc_chen@082709
01.[Bug] modify bandwidth requirement calculation for ast2100 8bpp modes, ycchen@072709
02.[Bug] fixed passmark performance test x64 - graphics test 640x480 mode hanged issue on ASUS P5B-MX wifi/ap
03.[Bug] Fixed S3 can't resume issue on DELL S99Q, ycchen@080309
04.[New] Modify for AST2150 DRAM default settings
v.0.90.00: yc_chen@071409
Bump driver version to v.0.90.00
---------------------------------------------------------------------------------
v.0.89.13: ycchen@070609
01.[Bug] Fixed Passmark BurnInTest Hanged Issue on customer's platform, ycchen@062909
v.0.89.10: ycchen@061909
01.[Bug] Fixed for Error Recovery no effect
v.0.89.07: ycchen@050809
01.[Bug] Fixed blue screen issue on Windows 2000, ycchen@050809
02.[New] Modify AST2100/2050 DRAM default settings by H/W request, ycchen@051109
v.0.89.05: ycchen@043009
v.0.89.06: ycchen@050509
01.[New] Fixed Error Recovery Issue
02.[Bug] Fixed the issue of missing PnP monitor in DTM - Common scenario stress IO test randomly
v.0.89.04: ycchen@041009
01.[New] Support Error Recovery
v.0.89.03: ycchen@040209
01.[Bug] Fixed Scrath incorrect issue if AST2100/2000 is as secondary
02.[Bug] Fixed AST2100/2200 detect incorrect issue
03.[New] Add Error Recovery Handling
v.0.89.01: ycchen@030609
01.[Bug] Fixed system hung issue when switch modes when disable engcaps, ycchen@020409
02.[Bug] Fixed Install driver failed on GA-73PVM if AST2200 is as secondary, ycchen@022309
v.0.89.00: ycchen@020209
01.[Bug] Fixed cursor disappear randomly issue, ycchen@012309
---------------------------------------------------------------------------------
v.0.88.07: ycchen@122908
01.[Bug] Fixed display garbage while secondary enabled on AST2100/2050/1100, ycchen@121408
02.[Bug] Fixed secondary can't enable properly when plug AST1150, ycchen@121408
v.0.88.05: ycchen@111108
01.[Bug] fixed display screen disappear randomly issue while running DTM - common scenario stress test
02.[Bug] Fixed AST1100 1280x1024x32bpp threshold issue, ycchen@111308
v.0.88.04: ycchen@100708
01.[Bug] Fixed WinS08 desktop display black & white after login, ycchen@100708
02.[Bug] Fixed KVM + CRT threshold issue on AST2100 8bpp modes, ycchen@100708
03.[New] Modify DRAM settings by H/W  Request, ycchen@102808
v.0.88.03: ycchen@100208
01.[Bug] Clear DPMS settings while system initial, ycchen@100208
02.[Bug] Modify AST2100 DRAM timing for unstable issue (restore to v.0.88.01)
03.[Bug] Disable Legacy IO/Memory access if as secondary
v.0.88.02: ycchen@090908
01.[New] Bump Version for AST1160
v.0.88.01: ycchen@090208
01.[New] Add AST1100/2050/2100 A2 Chip Identity, ycchen@090108
02.[New] Modify AST1100/2050/2100 DDR2 DRAM Timing by Jason's Request
v.0.88.00: ycchen@082808
001.[Bug] Fixed VGA2 Mirror Display on-board solution can't be detect properly, ycchen@082708
---------------------------------------------------------------------------------
v.0.87.01: ycchen@080108
001.[Bug] Fixed S1/S4 resume abnormal in VGA only with option ROM combination, ycchen@061808
002.[Bug] Fixed default dram timing table is incorrect
03.[New] Support AST2200/2150, ycchen@122908
v.0.87.00: ycchen@072908
01.[PATCH] Patch for AST2100/1100 A2 X-Window Compatible Issue, ycchen@072908
